jdenergylife.blogg.se

1. KEYSPAN DRIVER FOR MAC INSTALL
2. KEYSPAN DRIVER FOR MAC SERIAL
3. KEYSPAN DRIVER FOR MAC DRIVERS
4. KEYSPAN DRIVER FOR MAC SOFTWARE
5. KEYSPAN DRIVER FOR MAC DOWNLOAD

I have a 3.3v and a 5v version of the ∿TDI-Friend” style adafruit cable plugged into my laptop right now and no fewer than 11 various other FTDI based serial port devices connected to my home automation controller mac mini In addition to the standard plug in FTDI/RS232 devices the ttl level ones I use are something like this:

KEYSPAN DRIVER FOR MAC INSTALL

You don’t even have to install the drivers. I am just restarting with Xojo so I am behind about 19 years in programing skills.Īny FTDI chip based product is supported out of the box with recent OSX versions. Any knowledge you can share with me on this would be appreciated. I’m trying to keep it simple at this point to see if I can receive data through the Keyspan adapter. I receive a long list of these when the DataAvailable event fires (OutputArea.Text = OutputArea.Text + Me.Readall). The data I do receive looks like diamonds with “?” marks in the middle. The ITC232-A has a reset pin that when activated will cause the chip to reset and send out “Welcome to RVC” which can be picked up by the serial control in Xojo. Previous communications with RB 4.5 where: baud = 9600k or 57000k, bits = 3, stop = 0, parity = 0. I am now trying to use Xojo 2019 3.1 but have had no success sending and receiving serial data using the Keyspan adapter with current drivers.

KEYSPAN DRIVER FOR MAC SOFTWARE

I recently purchased a KeySpan USA-19HS USB to serial adapter in hopes that could rewrite with software using a current Mac OS. The issue now is the Wallstreet Laptop with a serial port built has becoming obsolete. The home automation system this chip controls has been pumping for 19 year 24-7. The Windows world (I got my Mac last summer.Nineteen years ago using Realbasic 4.5 I wrote a software program to communicate with a RMV Electronics ITC232-A control chip (still sold to this day: ) which is hardware independent and will work with any terminal or computer with an RS-232 serial port. Still much better than all my prior experience in My non-apple software to the latest version in anticipation of moving This thing sure looks flaky - it has me a bit worried as I move all I do see "Keyspan USB Serial Port (Com1)" on the Ports (COM & LPT) I rebooted WinXP via the Start-TurnOffComputer sequence.) What I was going to write to you, the Keyspan Serial Assistant opened (I would note, however, that even when I opened it to check It also shows on the Keyspan Serial Assistant listing with the same The USB devices list also shows at the bottom of theįusion "Virtual Machine" Tab on the Fusion top menu bar. The left-hand white-background pane is a list within Fusion of the To Snapshot." In all the fiddling I did today, it seems clear that "Settings" tab at the top of the Fusion window, right next to "Revert You probably can tell if its Fusion that is messing up by using the

Somewhere on the Keyspan site as using the same driver. I do see one difference, in that my Keyspan device is listed as a

KEYSPAN DRIVER FOR MAC DOWNLOAD

I did indeed download ver3.7sįrom the Keyspan website earlier today, dated Dec 12, 2007. Sorry for the confusion above - at this point I am just feeling luck to have hit a combo that works. It got very confusing along the way, as the system seemed to need WinXP restarts often along the way, and on occasion that "Connected" checkbox was unchecked.

For me the Keyspan port was then assigned to com5, and I reassigned it to com1 as above, as well as switching to the bulk mode on the aforementioned Advanced tab.Įven then, the Adapter did not come up on reboot - I found that I had to click on the Settings Tab at the top of the Fusion WinXP window, then click on the Keyspan unit in the left-hand pane of USB devices, and then click on the "Connected" box in the right pane. Then I found a tab in the Windows Keyspan Serial Assistant that allowed removing all Keyspan entries in the registry, uninstalled the Keyspan driver, and reinstalled it. I also reassigned com2 to com4, but I suspect that is not necessary. I had to go into the XP ControlPanel-System-Hardware-DeviceManager-Ports window, and reassign com1 to become com3 on the port's Properties-PortSettings-Advanced tab. It seems that WinXPsp2 on Fusion 1.1 defaults to setting up com1 and com2 as ports on some generic bus, which do not seem to correspond to any real physical port.

KEYSPAN DRIVER FOR MAC DRIVERS

The bulk mode was the last step needed to get my Keyspan port working.įor me the problem was that the Keyspan windows drivers (ver37s) installed the Keyspan port at the next highest com port, above the previous highest one.